Twin 12v 11″ SPAL Puller Fans Plus Davies Craig Fan Controller Kit.

Individually balanced for long life, the EF3580 Twin 11″ Puller Fan features fully sealed water & dust-proof motors of superior quality.

EF3580 TWIN 11″ SPAL THERMO FAN 

Spal Fan Model #: 2VA06-AP70/LL-37A
U.S. Part #: 30102052
Voltage: 12V
Flow Type: Puller
Blade Diam.: 11 inch (280mm)
Blade Type: Straight
Shroud Type: Open Shroud
Amps: 29.8
CFM: 2720
M3/H: 4610

Spal Twin 11″ Fan EF3580

DIGITAL THERMATIC FAN SWITCH KIT- PART NO: 0444

Davies, Craig designed Digital Thermatic Fan Switch Kit can be used with our Thermatic Fans, EWP’s and competitors Fans.

The sensor, a Temperature Probe (Air or Coolant Fitment) senses air temperature as it passes through the radiator with the sensor placed in the radiator fin section or the sensor can also be placed directly into the coolant system in combination with a Temperature Sensor Adaptor Kit (Part 0409) which is available from our store.

Sensor Wire length:

142cm in total (Wire from switch 112cm plus sensor connector 30cm)
Post 15-Dec-2021 = 320cm total (Wire from switch 290cm plus sensor connector 30cm)
*The sensor wire has been increased to 320cm from the 15-Dec-2021, batch date 2021

The switch can run 1 or 2 fans and be used for 12 or 24 volt applications. It has an adjustable temperature range of 40ºC to 110ºC (104ºF to 230ºF) which can show Centigrade or Fahrenheit.

Fan #1 will start once the temperature reaches the set temperature.
Fan #2 (if applicable) will start operation 10 seconds after fan #1 starts.
The fan/s will operate until the temperature falls by 5°C below the set temperature.

IP66 Rated:

Protected from total dust ingress
Protected from high pressure water jets from any direction, limited ingress protection
Not waterproof

KIT CONTENTS

DESCRIPTION                          UNITS

Digital Fan Switch IP66               1

Mounting Kit for Sensor Probe  1
Red 6mm Ring Terminal             1
Blue 6mm Ring Terminal            1
Blue Wire Joiner                           2
Self Tap Screw                               2
Instructions                                    1

24 Volt Application

Kit sold in 12 volt configuration, for 24 volt application, you will need to purchase 2 x 24 volt relays.

Simply search for part 10534 in our search bar (top right-hand side of website).

AIR TEMPERATURE APPLICATION

It senses air temperature as it passes through the radiator and has an adjustable temperature range of 40ºC to 110ºC (104ºF to 230ºF).
The Temperature Sensor is placed in the radiator fin section as close to the hot coolant inlet as possible, no need to cut hoses or can be placed directly into the coolant system.

WATER / COOLANT APPLICATION

The 0444 sensor can also be placed directly into the coolant system. You will need to use a Temperature Sensor Adaptor Kit (Part 0409) to assist with this type of fitment.

We also offer a Digital Thermatic® Fan Switch with 1/4″ NPT Thermal Sensor Kit, part number 0445.

SPECIFICATION

Max voltage: 12 to 27V (For 24V, relays need to be changed, not supplied in kit)
Max current: Rated to 30 amps per Fan (Maximum 40amp per Fan) Unit comes with 2 x 30 amp fuses and 2 x 40 amp relays
Relay setup: Dual relay
Sensor Wire length: 142cm in total (Wire from switch 112cm plus sensor connector 30cm) (Post 15-Dec-2021 320cm)
Speed: Single speed, 10 second delay to start up the second fan
Applications: Suitable for single and dual fan applications
Screen Display: LED digital temp display, actual temp + set temp
Temp Display: Centigrade or Fahrenheit
Temp settings: 40°c to 110°c  (104°F to 230°F)
Temp setting: Push Button
Circuit type: Pre-programmed micro controller
Output wires: Batt + Batt – IGN, AC Clutch, Fan #1, Fan #2 Thermistor Probe
Dimensions: 95x65x56 mm
Please Note: This Kit includes the Twin Fans and The Fan Controller, if required both the fans and the controller are sold separately in our store.

*All pictures shown are for illustration purposes only. The actual colours may vary from those shown depending on the device you are using to view the product or the angle of the item is photographed. Actual products may vary due to product enhancements or updates. The listing should be referred to for the description of the product, any questions should be asked prior to purchase.